This page will be updated regularly with new vendors and models. Check back if the manufacturers you need is not listed. You can also send an E-mail to sales@vibrasens.com if you request specific manufacturers to be added to the list.

Manufacturers	Manufacturer Part Number	VibraSens Part Number	VibraSens Best Buy (1)	Note
Endevco/U.S.A. Meggit Group
Vibro-Meter/CH Meggit Group	CE680M411
Wilcoxon/U.S.A. Meggit Group	793	101.21-6-1	101.21-6-3	Wilcoxon:compression design (2)
797	103.22-6-1	103.22-6-2	Wilcoxon:compression design (2)
746	101.01-6-2	VibraSens:use IP69K M12 overmolded cable (1)
782A	101.21-6-1	101.21-6-2	Wilcoxon:sensitivity ±15%
784A	105.01-6-1	105.01-6-3	wilcoxon:sensitivity ±20%, flexure (7)
785A
786A
787A
788A	101.21-6-1	101.21-6-2	wilcoxon :flexure design (7)
797	103.02-6-1	103.02-6-2	not exactly same housing
793L	101.01-9-1	101.01-9-2	compression design (2)
797L	103.02-9-1	103.02-9-2	not exactly same housing
793V	111.01-6-1	111.01-6-2	Wilcoxon:compression design (2)
793	101.21-6-1	101.21-6-3	Wilcoxon:compression design (2)
793-6	101.11-6-1	Wilcoxon:compression design
793T-3	101.21-6-2-T0	Wilcoxon:compression design (2)
793VT	111.21-6-2-T0	Wilcoxon:compression design (2)
793-6 fire	101.11-6-1	150°C hybrid thick film electronic Wilcoxon:compression design (2)
797-6 Fire	103.02-6-1	150°C hybrid thick film electronic Wilcoxon:compression design (2)
PC420A	125.01-A-1	125.01-A-2
PC421	127.01-A-1	127.01-A-2
PC423	use IP69K M12 overmolded cable
PCB-IMI/U.S.A	603C01	101.21-6-1	101.21-6-2	PCB:Dynamic limited at 50g
623C01
606B01	103.22-6-1	103.22-6-2	PCB:Dynamic limited at 50g
Dytran/U.S.A	3176B	101.21-6-1	101.21-6-2	Dytran:Dynamic limited at 50g
3184E
3202A	103.22-6-1	103.22-6-2	Dytran:Dynamic limited at 50g
3202A
SKF/U.S.A.	CMSS 2100	101.21-6-1	101.21-6-2	Wilcoxon sourcing
CMSS 2106	101.21-6-1	101.21-6-2	Wilcoxon sourcing
CMAC 5209	10.01-B22-I02-61-02
CTC Online U.S.A.	Connection Technology Center
AC102-1A	101.21-6-1	101.21-6-3	CTC dynamic range is 50g
AC150-1A	101.21-6-1	101.21-6-3	CTC dynamic range is 50g, sensitivity ±15%
AC210-A1
AC104-1A	103.22-6-1	103.22-6-2	CTC dynamic range is 50g
AC184-1A	104.01-6-1	104.01-6-2	CTC Sensitivity is ±10%
AC211-1A
AC135-1A	101.01-9-1	101.01-9-2	CTC Sensitivity is ±10%
AC136-1A	103.02-9-1	103.02-9-2	CTC Sensitivity is ±10%
AC131-1A
AC224-1A	103.22-3-1	103.22-3-2	VibraSens is slightly bigger
TA102-1A	101.21-6-3-T0	CTC dynamic range is 50g
TA104-1A	103.22-6-2-T0	CTC dynamic range is 50g
TA184-1A	104.01-6-2-T0	CTC dynamic range is 50g
TA131-1A
TA135	101.01-9-2-T0	CTC Sensitivity is ±10%
AC107-1A	101.11-6-1	CTC Sensitivity is ±10%/range=50g
AC108-1A	103.02-6-1	CTC Sensitivity is ±10%/range=50g
AC188-1A	104.11-6-1	CTC Sensitivity is ±10%/range=50g
VE101-1A
VE102-1A
LP202-1A	125.01-V-1	125.01-V-3-DA
LP204-1A	127.01-V-1	127.01-V-2-DA
LP284-1A	128.01-V-1	128.01-V-2-DA
LP302-1A	125.01-A-1	125.01-A-3-DA
LP304-1A	127.01-A-1	127.01-A-2-DA
LP401-1B
LP402-1B	125.01-V-2-DA
LP404-1A	125.01-A-2-DA
Monitran / U.K.	MTN/1100	101.21-6-1	101.21-6-3	Monitran:compression design (2)
MTN/1100S	103.22-6-1	103.22-6-2	Monitran:compression design (2) (3)
MTN/1100SW	101.21-6-2	VibraSens:use IP69K M12 overmolded cable (1)
MTN/1187	125.01-A-	125.01-A-3	Monitran:compression design (2)
MTN/1185-2P	125.01-V-1	125.01-V-3	Monitran:compression design (2) (5)
MTN/1186	125.01-V-3-DA	Monitran:compression design (2) (5)
MTN/1600	111.01-6-1	111.01-6-2	Monitran:compression design (2)
MTN/1188	125.01-A-3-DA	Monitran:compression design(2)
MTN/1010	108.01-6-4	Monitran:Base not isolated (6)
MTN/1020	108.01-6-4	Monitran:Base not isolated (6)
Hansford / U.K.	HS-100	101.21-6-1	101.21-6-3	Hansford:compression design (2)
HS-100S	103.22-6-1	103.22-6-2	Hansford:compression design (2) (3)
HS-120	105.01-6-3	Hansford:Plastic M12 connector max 90°C
HS-420	125.01-V-1	Hansford:compression design (2) (5)
HS-421	125.01-VR-3-DA	Hansford:compression design (2) (5)
HS-422	125.01-A-1	Hansford:compression design (2) (5)

Note: The information found in the VibraSens Part Number Crosser section of our website is intended for reference purposes only. VibraSens does not guarantee the accuracy of this information and provides this section as a service to our customers. Well know manufacturers like Bruel&Kjaer / Kistler / MMF are not included in this list because there are mostly laboratory acceleromleters provider.

1. VibraSens Best Buy : If you buy a VibraSens sensor with M12 connector you'll save money on the overmolded cable compare to Mil-C-5015 solution. M12 overmolded cable assembly have a submersible depth of 150 meters/500 feet. M12 overmolded cable could aslo be shipped with a stainless steel armored conduit.
2. Compression design is an old design that should not be used anymore.Limitations are : thermal transient sensitivity, base strain sensitivity, high transverse sensitivity, 2Hz lowest frequency, Low resonant frequency, ....
3. Sensor cover not welded -> no hermeticity
4. Sealed with stuffing gland and epoxy : suceptible to epoxy cracks and ageing. NO GLASS SEAL Sealing.
5. Old Compression design : 4-20 mA signal will be sensitive to cable motion (base strain sensitivity)
6. Base not isolated: signal will be distored by 50 Hz.
7. Flexure design limitations are : 2Hz lowest frequency, thermal transiant sensitivity, Low resonant frequency, ....
8. Using the M12 connector with 4 Pins, VibraSens is able to offer (free of charge) Dynamic acceleration / Dynamic velocity